-
edward ericson replied to the topic Carlisle 2020 in the forum Clubs and Show 5 years, 6 months ago
It is reported that Carlisle Events will change your showfield registration to 2021 on request. I’ve not requested this yet but at least a couple of guys have.
-
John Cable posted an update 5 years, 6 months ago
Just found out about the Club from the Speedster’s owner of Club forum where I on a Speedster which is built out in Phoenix where I winter.
As you see from my pictures I… -
John Cable posted an update 5 years, 6 months ago
I’ve owned this for 10 years put a new engine in and also a freeway Transmission
Finally got a emergency brake/parking brake because I lost brakes last summer and w… -
John Cable became a registered member 5 years, 6 months ago
-
Dale Schumacher replied to the topic Carlisle 2020 in the forum Clubs and Show 5 years, 6 months ago
Unfortunate but I guess the sign of the times – looking forward to VA Beach even more – hope that works out.
-
billnparts replied to the topic Carlisle 2020 in the forum Clubs and Show 5 years, 6 months ago
Can’t say I didn’t see this coming. Maybe things will improve enough to enjoy VA Beach this fall.
-
edward ericson replied to the topic Carlisle 2020 in the forum Clubs and Show 5 years, 6 months ago
Carlisle 2020 Cancellation… A
fter holding out as long as possible for Covid – 19 situation to improve and after much sole searching, both Alan Merklin and I have decided that in the best interest of health and safety to cancel our Carlisle 2020 event. This was very difficult decision. We are sure that this is disappointing to all of our TDr…[Read more]
-
crash55 and
Eric Fowler are now friends 5 years, 6 months ago -
crash55 and
dggrant are now friends 5 years, 6 months ago -
crash55 started the topic maiden cruise in the forum General Discussion 5 years, 6 months ago
took my new duchess for the 1st ride last night . every thing is OK cannot wait for Carlisle
-
Dale Schumacher replied to the topic Introduction in the forum General Discussion 5 years, 6 months ago
Eric,
Welcome – I think I saw you over in the Speedster site? Anyway welcome to the dark side 🙂
I have a Speedster ( in process for to many years now ) and my finished MG TD – see you at Carlisle.
-
dggrant replied to the topic Introduction in the forum General Discussion 5 years, 6 months ago
Hi Eric:
Great to have another in Pittsburgh.
Bill (Crash55) has talked me into Carlisle this year so I’ll be taking Annie for the drive. Would be great to meet up with you and your MG at sometime (I’m in Sewickley).
Regs
dan
-
edward ericson replied to the topic Moto-Meter with Radiator Cap in the forum Site 5 years, 7 months ago
Looks great!
-
Robert Stagmier replied to the topic Moto-Meter with Radiator Cap in the forum Site 5 years, 7 months ago
Update:
Coupling Nut worked a charm!
-
-
Paul Mossberg replied to the topic New member Daytona in the forum TD Replicas 5 years, 7 months ago
Welcome aboard Robert!
Nice ride!
-
Dale Schumacher replied to the topic update on my life in the forum General Discussion 5 years, 7 months ago
Ryan,
My grill is a cut down original TD grill. They come up on ebay and other places from time to time but expensive. Most original ones are 600.00 to 1000.00 in good shape. At Carlisle two years ago a guy was trying to sell one in decent shape for around 400.00. Bill almost bought it to replace the one he dented in on of his crashes but I think…[Read more]
-
billnparts replied to the topic Spyder work in the forum General Discussion 5 years, 7 months ago
Very cool, Ed. Looks like it tracks straight, stops straight, sounds good. Sweet!
-
edward ericson replied to the topic Spyder work in the forum General Discussion 5 years, 7 months ago
I posted a short test-drive vid yesterday.
<iframe width=”540″ height=”314″ src=”https://www.youtube.com/embed/qPXNBe_9908″ frameborder=”0″ allow=”accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture” allowfullscreen></iframe>
-
Dale Schumacher replied to the topic Tips for Cutting Fiberglass? in the forum General Discussion 5 years, 7 months ago
I am sure it would – maybe 3/4″ square aluminum – light and rigid. Can buy at Lowes or Home Depot in the hardware dept.
Bar stock might flex down ( sag ) a bit – not rigid like square or triangle stock in my opinion.
- Load More
