@crash55
Active 2 years, 9 months ago-
edward ericson replied to the topic 2016 Calendar in the forum General Discussion 10 years, 4 months ago
Sorry for all the trouble, boys. Hoping you can just refresh your browser and continue from there.
-
edward ericson replied to the topic 2016 Calendar in the forum General Discussion 10 years, 4 months ago
hold on. I’m sorting it now.
Try this link:edsnova2015-11-29 20:51:58
-
edward ericson replied to the topic 2016 Calendar in the forum General Discussion 10 years, 4 months ago
Try also: https://www.shutterfly.com/myProjects/default.sfly?fid=48a75738ae0c910dbcfd7207a7b1fe91
Let me know what (if anything) you get. -
edward ericson replied to the topic 2016 Calendar in the forum General Discussion 10 years, 4 months ago
made the calendar and ordered. regular is about $32 shipped. I put in a discount code and got it to $27.
the code was 25RMNNow I’m trying to find a way to let you all order the calendar… first attempt.seems to not work…so we tryedsnova2015-11-29 21:55:19
-
edward ericson replied to the topic Door Alignment – Chassis Flex (?) in the forum General Discussion 10 years, 4 months ago
Bottom line: try not to worry too much.
My experience with a somewhat rusty pan is that the doors more or less fit OK. The passenger side is a bit “sticky” if left unused for a time.The torsion housings are as follows: Front: the two big (2 1/4 inch? diameter) tubes, one atop the other, separated by a few inches of space, which run crosswise behind… -
edward ericson replied to the topic 2016 Calendar in the forum General Discussion 10 years, 4 months ago
Whelp, Shutterfly chewed on the pictures for 4 hours and then froze. So I will rebuild the calendar & try again.
-
Dale Schumacher replied to the topic 2016 Calendar in the forum General Discussion 10 years, 4 months ago
Thanks for your efforts Ed.
I guess I don’t need to take pictures to get in a calendar. -
Dale Schumacher replied to the topic Door Alignment – Chassis Flex (?) in the forum General Discussion 10 years, 4 months ago
John,
First of all the Speedster uses a shortened pan while ours use the full original pan. In addition if you look underneath you will see that the fiberglass fits to the original pan to add strength.I understand that sometimes the doors do get out of alignment but if you use the rear torsion bars to jack the rear and the front beam for the… -
edward ericson replied to the topic Profile drawing in the forum VW Based Kits 10 years, 4 months ago
I think the center of gravity on these cars is well below the tops of the tires (2 feet off the ground). Probably more like 14-15 inches in a VW-based car. It does make for a naturally good chassis design and its why you can keep up with pretty much all the LBCs of the 1950s and ’60s pretty easily.
They do lose traction though: VW-based TDs tend to… -
edward ericson replied to the topic 2016 Calendar in the forum General Discussion 10 years, 4 months ago
OK so my usual Cafe Press system seems to be shut down. I can’t find a spot on their web site where you can make a calendar with more than one page of pictures. I’ve got it uploading to Shutterfly now and will let everyone know how to order.
They’re asking $25 a pop plus, I’m sure, shipping. I feel like these ought to be cheaper but it is what it is. -
billnparts replied to the topic Profile drawing in the forum VW Based Kits 10 years, 4 months ago
Page 4 of the Fiberfab Ford Pinto Assembly Manual has the same type photo with the Pinto and MGTD superimposed.
-
billnparts replied to the topic 2016 Calendar in the forum General Discussion 10 years, 4 months ago
Great job once again, Ed.
Just let us know once they’ve gone to press. -
Vicenç Feliú replied to the topic 2016 Calendar in the forum General Discussion 10 years, 4 months ago
Awesome! I’m gonna need a handful of these. Great job, Ed!
-
edward ericson replied to the topic 2016 Calendar in the forum General Discussion 10 years, 4 months ago
rest of draft…
-
edward ericson replied to the topic 2016 Calendar in the forum General Discussion 10 years, 4 months ago
Draft. Let me know what you think.
-
edward ericson replied to the topic Profile drawing in the forum VW Based Kits 10 years, 4 months ago
That looks pretty close.
-
edward ericson replied to the topic Pow Bang Pop…. in the forum General Discussion 10 years, 4 months ago
Great news! And a great day to cruise about. Lookin’ good, gentlemen.
-
edward ericson replied to the topic Thanksgiving, 2015 in the forum General Discussion 10 years, 4 months ago
Happy Thanksgiving, everyone. Soup stock is on (MAN O MAN the turkey came out good this year!) Karen’s brother and his family came over and so did her mother (and her little fluffy white dog) and sister-in-law’s parents. Those two loved Bridget.
The dogs got along too.Great day. Everyone went home happy. Best to all you guys & your loved ones. It… -
Dale Schumacher replied to the topic Pow Bang Pop…. in the forum General Discussion 10 years, 4 months ago
Dean Have to look but might have a heat risor in my stuff someplace if you have a hole in yours.Let me look – yours for the asking. Going driving today?Getting ready to go out for a run.60 degrees going on 65.
-
edward ericson replied to the topic Pow Bang Pop…. in the forum General Discussion 10 years, 5 months ago
Make sure the preheat manifold is not rotted out. Mine was–and hidden behind one of the air hoses that comes up through the tin on each side of the engine, so I didn’t see it. She’d backfire like crazy on decelleration until we patched it up with tape…
- Load More
