Say guys, as a radio goes if you want a retro have you thought of looking in junk yard ? there many late model and older ones that may fit what your needs are.. if you want a british look factory MG radio box has speekers and a switch and looks good bolted to the floor. Dan

Greg , i have a simple dash mounted mirror ,just simple 2 screw mount and looks good , and works well with the look of the car… Dan

Park, is in the wiper motor transmission  there is like cam that kills power at the park position that is why there 2 power wires.  Dan

Donna , I have one for a boat that i got from Bass Pro Shop with park for i ‘m thinking  under $10.00  it adjusted to a full 1.25 inches Good luck  Dan R

Don  I don’t know part numbers for a longer cable but i have always had my best luck NAPA parts stores they seem to be more in tune with odd stuff more so than outher places .. GOOD LUCK  Dan

Greg , I thing you have the information now , but i would also do a compression test. most of these engines are old and may need a valve job, good luck    Dan

Dick,,mine had 3 at the grill 2 on the rear of the side panel 5 under the fender I had to put new wire connectors to the headlights . it takes longer to put it all back together , but not long ,just keep the screws loose untill all in and lined up then tightened use stainless steel bolts ,washers, and nuts for next time 

I to have been asked,,, Rolls. Stutz, Ford T, Morgan and those are the people that know the names of neet cars but do not know what they looked like I think it is great that people ask.  Dan R

 Larry,, i guess I was lucky the bottom bolts were 3/8 hex, easy to remove and were also stainless the screws you can see were also stainless i replaced the slotted screws with Philips using stainless with trim washers . all of about 15 minutes to remove. It is longer to replace the panels but not bad . I guess this winter next year i will cut th…[Read more]

WOW 150 pounds each about 225$ times 5 $900.00 i would look on ebay Dan R

Dick ,,it is not hard just a lot of screws. the side panel is light and just slide up and out. TIME is the trouble  Dan R

Larry, I was thinking of cutting the lower side panel at the fender and using the same type of lock as a TD but used the screws to put it back but I will in the end up doing  it if i ever have to remove the side panel again . I was thinking of using a garage type of lock.  Dan R

I did my rear lights with a wire harness using trailer light wire for 1/2 the price of rolls and are all color coded and together.  Dan R

 I think parts Guys come to 2 types those that know and those that think they do!! I found a store N.P.A. the guyes there are all older and most know with out the book and have never made a mistake .

 Hay guys why don’t you just go to an electric pump ?? quick and simple Dan.

ONE NEVER KNOWS ,DO ONE ……..if you need one try…..

 ED, I think you are on the mark my chevette powered stops as good as any with power brakes . i could net get power brakes in and  behind the intake .But if you need power brakes look in to a system from a early Hyundai they there power system in the right side with a cross over system for the brakes ‘mid  80’s’ Excel       Dan

Greg ,,if your car is/ was like mine do the filters again also the one in the carb. if crud passes through the filter and gets in the carb. it can do just what you describe . Dan

You don’t see all that many dirt track Chevette;s 25 /30 years ago there were alot you could have bought that intake and carb. setup from Chevy and Pontiac racing parts ,,high revving engine setup . makes me see just how old I AM…BUT WOW IT LOOKS GREAT do you have the headers? there were a set of mandrel bent tube headers that were available…[Read more]

what a waist of a body and frame   all that time and CASH $$$    Dan